The device, service, Audi A3 repair (c of 1997 of release) - Dismantling amortization rack/removal and shock-absorber installation / a screw spring//A3 Audi artistwave.ru

Audi A3

since 1997 of release

Repair and car operation



Audi A3
+ Maintenance instruction
+ Current leaving and service
+ Engine
+ Systems of cooling, heating
+ the Power supply system and production of the fulfilled gases
+ engine Electric equipment
+ Manual box of gear shifting
+ Automatic transmission and models with a full drive
+ Coupling and power shafts
+ Brake system
- Suspension bracket and steering
   - Forward suspension bracket
      Removal, check and installation of a spherical support
      Removal and installation of an amortization rack and case of the wheel bearing
      Dismantling amortization rack/removal and shock-absorber installation / screw spring
   + Back suspension bracket
   + Steering
+ Body
+ Onboard electric equipment
+ Elektroskhema







Dismantling amortization rack/removal and shock-absorber installation / screw spring

GENERAL INFORMATION

Elements of an amortization rack


ATTENTION

The spring to be under loading, is compressed by the adaptation, Dangerously!


1–shock-absorber. Replace only in a set
2–buffer of a course of compression
3–protective casing
4–spring screw.
5–plate
6–bearing persistent
7–support of an amortization rack
8–nut, 60 N • m. After each otvorachivaniye replace. Turns away only after spring compression by the adaptation.
9–an aligning cup, 60 N • m
10-nut, 60 N • m. Being self-stopped, surely replace.

REMOVAL

PERFORMANCE ORDER
1. Remove an amortization rack, address to the subsection Removal and installation of an amortization rack and the case of the wheel bearing.
ATTENTION

The spring is under big effort. To have possibility of removal of the shock-absorber, the spring should be compressed the corresponding adaptation.
Nut of the shock-absorber it is necessary to turn on only in that case when the spring is compressed by the adaptation!


2. Compress a spring the corresponding adaptation – 1–and boots – 2–.

ATTENTION

Insert the adaptation into spring rounds so that it is reliable to capture rounds and the adaptation could not slip out. The spring is compressed by big effort therefore apply only the reliable adaptation. At all do not pull together a spring with a wire. Danger of accident!


3. Unscrew a nut of fastening of an amortization rack, holding thus from a provorachivaniye a face key of 7 mm. The cranked cap key is necessary for a nut. In case of use of the tool – 3–(AUDI – 3186 or HAZET 2593-21 complete with 2100-07) can be applied to a tightening a usual dinamometrichesky key.
4. Slowly unload a spring, remove separate details.
5. Check the shock-absorber, address to subsection shock-absorber Check.
6. If necessary utilize the shock-absorber, address to subsection shock-absorber Utilization.

INSTALLATION


ATTENTION

There are springs of various classes of accuracy. It is necessary to apply only identical marking (color marking).


PERFORMANCE ORDER
1. The new spring is protected from corrosion by a varnish. Before installation of springs check integrity of a varnish covering and if necessary restore it.
2. Compress a spring the corresponding adaptation and insert into the shock-absorber. Watch that the end of a spring adjoined to an emphasis of the bottom plate.
3. Collect an amortization rack according to an illustration Elements of an amortization rack.
4. Tighten a new nut the moment of 60 N • m, holding thus a rod a face key of 7 mm.
ATTENTION

To establish a dinamometrichesky key, as the tool it is possible to apply AUDI – 3186 or HAZET 2593-21 complete with 2100-07 to deduction from a provorachivaniye.


5. Slowly unload a spring.
6. Establish an amortization rack, address to the subsection Removal and installation of an amortization rack and the case of the wheel bearing.