Audi A3

since 1997 of release

Repair and car operation

Audi A3
+ Maintenance instruction
- Current leaving and service
   Schedule of routine maintenance
   General information on control
   Check of levels of liquids, control of leaks
   Check of a condition of tires and pressure in them
   Replacement of impellent oil and oil filter
   Check of a gear belt of a drive of GRM on existence of damages, wear measurement
   Check of brake system
   Check of fuel system
   Rotation and replacement of wheels. Antisliding chains
   Check of a condition and replacement of hoses of an impellent compartment, localization of leaks
   Check of functioning of system of cooling
   Check of a condition of system of production of the fulfilled gases
   Visual check of tightness of a box of gear shifting
   Check of a condition of components of a suspension bracket and steering
   Check of a condition of protective covers of power shafts
   Greasing of clamps of doors and lock cylinder
   Condition check, adjustment and replacement of brushes of screen wipers
   Visual control of a seat belt and safety cushion block
   Check of a condition of the battery, care of it and charging
   Check of level of the RKPP transmission oil
   Replacement of the filter of air of salon
   Replacement of a filtering element of the air filter
   Replacement of brake liquid
   Check and replacement of spark plugs
   Replacement of the fuel filter of the diesel engine
   Check of level of liquid of system of hydrostrengthening of a wheel
   Check of level of liquid of the main transfer of automatic transmission
   Oil replacement in coupling of Haldex of models with a full drive
   Check of a condition of driving ridge belts
   Check of level of the AT transmission liquid
+ Engine
+ Systems of cooling, heating
+ the Power supply system and production of the fulfilled gases
+ engine Electric equipment
+ Manual box of gear shifting
+ Automatic transmission and models with a full drive
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment
+ Elektroskhema

Check of level of liquid of system of hydrostrengthening of a wheel

PERFORMANCE ORDER

1. Periodically check liquid level in system of hydrostrengthening of a wheel in order to avoid emergence of problems with management of the car, such, as damage of the steering pump. Act as follows.
ATTENTION Do not hold a steering wheel turned against the stop in this or that party more than five seconds. It can put out of action the steering pump.
2. The tank of system of hydrostrengthening of a wheel is located in an impellent compartment and has an unscrewing cover with built in in it measuring the shchupy.
3. Park the car on an equal platform and cock the parking brake. Level of oil can be checked in a cold or heated-up condition (since +50°С). Here check in a cold condition is described. Pay attention to the remarks provided in the end of the Section if level of oil has to be checked in a heated-up condition.
4. The car should not be heated-up, the engine should not work. Forward wheels should stand directly.
5. Unscrew by means of a screw-driver a tank stopper (the shooter on an accompanying illustration). For this purpose insert a screw-driver core into a stopper groove.
6. Wipe a pure rag the level index under a cover.
	7. Manually screw and again unscrew a stopper. Oil level on the index should be in a range of 2 mm above or MIN markings are lower.
ATTENTION As a rule, level of oil should not go down. If level of oil decreases, it is necessary to eliminate a leakage on HUNDRED AUDIS. If level of oil lies above the specified range, oil is necessary for pumping out.
8. Oil is added surely only new as even insignificant pollution can lead to hydrosystem failures.
9. Wrap a stopper by means of a screw-driver.

The remark on check on the engine, heated-up to working temperature:

Warm up the car, having executed a trial trip. Oil should get warm to temperature near +50°С. Check oil level on the working engine. Thus forward wheels should stand directly. Oil level at the screwed cover should be between MIN and MAX marks on the other side of the index.