Removal and installation of the handle of a forward door and lock cylinder Handle of a forward door and lock cylinder
1–peak
2–lining
3–lock cylinder
4–bracket rotary
5–door handle
6–screw, 5 N • m | 7–cover of the lock of a door
8–safety draft. For removal disconnect at an element of a drive–9–.
9–drive element
10-safety draft of the cylinder of the lock | Handle of a forward door. Models with chassis number since 8L XA 000 001
ATTENTION The handle represented on an illustration is established on cars with chassis number since
8L XA 000 001.
1–handle support. The cylinder of the lock belongs to a support and cannot separately act in film.
2–lock finger. At installation the stopper should grasp the sharnirny lever completely. | 3–sharnirny lever
4–door handle |
ATTENTION
Since chassis 8L XA 000 01 number, the lock and the handle of the changed design is put. Removal of the handle of the changed design is considered in the subsection Removal and installation of an internal slip covered.
The handle and the cylinder of the lock can act in film separately. For this purpose it is necessary to follow the corresponding instructions.
REMOVAL
| PERFORMANCE ORDER |
| 1. Remove the holder of adjusting elements of a door, address to the subsection Removal and installation of a forward door and the holder of adjusting elements. | | 2. Disconnect a cover–7–and take out it below from the door lock. | | 3. Disconnect safety draft–8–at the handle. | | 4. Disconnect safety draft–10–at the lock-3-cylinder. | | 5. Turn a bracket–4–down (against the movement direction) and take out the lock cylinder. |
| 6. Turn out the screw-6-. |
| 7. Remove a peak–1–. | | 8. Remove a lining–2–. | | 9. Remove from within the handle-5-. | | INSTALLATION
|
PERFORMANCE ORDER |
| 1. Establish a peak–1–lined–2–. | | 2. Establish from within the handle of a door–5–and compress it with a slip. | | 3. Fix the handle the screw – 6–at a slip. | | 4. Insert the cylinder of the lock-3-and fix a bracket–4–. For this purpose establish a bracket at the cylinder of the lock and incline forward (in the movement direction). | | 5. Fix the sharnirny plug-2-(if she acted in film) in the spuskny lever-1-at the lock cylinder. | | 6. Connect lock draft–3–cylinders of the lock to the sharnirny plug-2-. | | 7. Insert lock draft–3–into a clip – 4–. | | 8. Insert lock draft–1–into a clip – 2–so that the lever-4-had a gap and = 1 mm. | | 9. After adjustment of a gap displace the plug-3-at a clip–2–up and thus fix lock draft. | | 10. Connect lock draft–8–at the handle-5-(address to an illustration the Handle of a forward door and the lock cylinder). | | 11. Put from below a cover–7–and fix it from above. | | 12. Insert the holder, address to the subsection Removal and installation of a forward door and the holder of adjusting elements. | |
Removal of an overlay of the handle
| PERFORMANCE ORDER |
| 1. Pull the handle up. | | 2. Take out a small screw-driver a lock level from the handle in the direction of an arrow and take out the handle. | | 3. Remove outside a handle peak. | |
Models with chassis number since 8L XA 000 001 REMOVAL
| PERFORMANCE ORDER |
| 1. Remove facing of a door and the holder. | | 2. Take out a lock finger–2–and lift up the sharnirny lever-3-. |
| 3. Release a screw-driver a level at a handle-1-support. | | 4. Remove a support of the handle and the lock cylinder with the handle. | |
INSTALLATION
| PERFORMANCE ORDER |
| Installation is carried out in return sequence. |
|
|
